The correct response is not to immediately stop using all amino silicone oils. Instead, use blank controls and step-by-step testing to identify the stage at which yellowing occurs.
Amino silicone oil forms a soft film on the fibre surface and usually provides a noticeable soft, smooth and slippery handle.
However, some amino structures are more likely to change colour when exposed to heat and air.
Published studies indicate that amino-group type, amino content, curing temperature and treatment time can all influence thermal yellowing. Therefore, the assumption that “the softer the handle, the more suitable the product is for white fabrics” is incorrect.
The following factors should also be investigated:
Whether fabric pretreatment was sufficient
Residual alkali, bleaching agents, softeners or other auxiliaries
Changes in the working-bath pH
Compatibility between optical brighteners and finishing agents
Excessive setting temperature or residence time
Impurities introduced by process water or equipment
The fabric’s inherent tendency toward thermal yellowing
If an untreated blank fabric also turns yellow after undergoing the same heat-setting process, the fabric and processing conditions should be examined before concluding that the finishing agent is defective.
This option is suitable when a clearly soft and smooth handle is still required. Selection should consider amino structure, dosage and heat-setting conditions rather than relying only on the product name.
Structural modification can provide different balances among softness, hydrophilicity and yellowing resistance. The final result depends on the specific product structure and fabric system.
This can be considered when hydrophilicity, soil release or moisture absorption is more important. However, handle and wash durability must be confirmed through fabric testing.
If one product cannot simultaneously provide whiteness, softness, hydrophilicity and wash durability, a combination of different silicone finishing agents may be evaluated.
Emulsion stability and ionic compatibility must be verified before adopting a combined system.
Before selecting a silicone finishing agent, provide at least:
Fibre type and fabric colour
Current finishing-agent type and dosage
Working-bath pH and ionic system
Drying and heat-setting temperatures and residence times
Target handle: fluffy, soft, smooth, slippery or hydrophilic
Optical brighteners, antistatic agents and other auxiliaries used
Whether yellowing appears after heat setting, storage or light exposure
A specific silicone-oil grade should not be recommended when these conditions are unknown.
Process the fabric under the same conditions without adding the softener. This determines whether the fabric or heat-setting process itself causes yellowing.
Remove other non-essential additives and evaluate the existing finishing agent alone.
Change one variable at a time to identify which factor has the greatest influence on whiteness.
Evaluate low-yellowing amino silicone oils, modified amino silicones and other suitable silicone materials.
Compare:
Whiteness
Softness and handle
Hydrophilicity
Wash durability
Emulsion stability
Compatibility with other auxiliaries
Optimising only softness while ignoring whiteness or process stability can create new problems.
As a full-chain silicone solutions provider, IOTA SILICONE OIL (Anhui) CO., LTD. can help screen suitable directions among amino silicone oils, polyether-modified silicone oils and other textile silicone materials according to the fabric, process, target handle and observed yellowing.
The final formulation and process conditions should be determined through testing on the customer’s actual fabric.
No. Fabric residues, optical-brightener compatibility, working-bath pH and heat-setting conditions may also cause yellowing.
No. Amine value is only one influencing factor. Amino structure, dosage, temperature and treatment time must also be considered.
Not necessarily. White fabrics usually require a balance among softness, whiteness, hydrophilicity and wash durability.
It may reduce thermal yellowing, but it may also affect film formation and handle. Temperature and residence time should be adjusted together and verified through controlled testing.
It can be considered for hydrophilic finishing, but its effects on whiteness, handle and wash durability must be verified on the actual fabric.
Prepare blank fabric, single-finishing-agent samples and samples processed at different temperatures and times. Then compare the whiteness before and after heat setting.
Yellowing should be diagnosed through controlled testing. The right solution is to balance whiteness, softness, hydrophilicity, wash durability and process stability—not simply to replace the amino silicone oil.
